Electrical · Pricing
How to price electrical jobs without guessing
Electrical work has its own version of the pricing trap, and it springs the same way: a number built on a journeyman's wage, or on a materials multiplier someone taught you years ago — "double the parts, add an hour" — instead of on what the job actually costs your shop to deliver. The work is licensed, the parts are expensive, and the jobs are short, which means the unpaid time around each job is a bigger slice of your day than in almost any other trade. Here's the whole method, with electrical numbers.
The trap: pricing off the wage or the multiplier
Two shortcuts run most small electrical shops. The first is wage-plus: take what you pay (or used to make) per hour, add a bit, and call it the rate. The second is the materials multiplier: double or triple the parts cost and let labor ride along inside it. Both feel fast. Both ignore the same three things — the burden on every wage dollar, the hours in a week nobody pays for, and the permit and inspection costs that are specific to electrical work. The four steps below replace both shortcuts.
Step 1: Find your true hourly cost
Your labor cost is not your wage. It's the wage plus payroll taxes, workers' comp, insurance, paid time off, and benefits — the burden, which runs 25–40% on top of wages for most small shops. A licensed electrician at $38/hour with a 30% burden costs the shop about $49.40 for every hour on the clock, before the truck, the fuel, or a single breaker.
Electrical adds two costs other trades feel less: permit fees and inspection time. The permit itself is a pass-through cost that belongs on the job (you'll see it as its own line in the worked examples). The inspection is subtler: waiting on an inspector, meeting one mid-job, or returning for a re-inspection is paid time that produces no billable work. It doesn't get its own line in the price — it gets absorbed by Step 2, which is why Step 2 matters so much in this trade.
Step 2: Count only billable hours
A tech is paid for 40 hours a week but bills maybe 20–25 of them. In electrical service work the leak is worse than in install work, because the jobs are short: a two-hour repair can carry forty minutes of driving, a supply-house run, and twenty minutes of paperwork. Drive time between small jobs is the electrical billable-hour killer — three or four calls a day means three or four unpaid trips.
Do the division honestly. If your techs bill about 55% of paid hours, every billable hour has to carry the cost of the other 45% too: $49.40 ÷ 0.55 ≈ $90 per billable hour just to cover labor. That's the loaded labor rate the worked examples below use — before materials, before overhead, before a dollar of profit.
Step 3: Materials, and the markup-vs-margin trap
Electrical materials are where multipliers go to die. A panel, a run of copper, an EV charger circuit — the parts on a single job can exceed the labor, so a sloppy markup assumption swings the whole price. Two rules keep it straight:
- Mark up materials deliberately, not by habit. Your markup covers procurement time, warranty risk on parts you supply, and the capital sitting in truck stock. Know the percentage and put it in your rate setup — don't let it hide inside a doubled guess.
- Never confuse markup with margin. A 20% markup on cost is only a 16.7% margin on price. If your target is a 20% margin, you divide total cost by 0.80 — you don't multiply by 1.20. On a $2,000-cost job that confusion is worth $100, straight out of profit, on every single job.
Then add your overhead share — truck, fuel, insurance, software, phones — as a percentage of job cost, the same way the plumbing method does it. The examples below use 15%.
Worked example #1: a 200-amp panel upgrade
The job every electrical shop quotes and half of them underprice. Round numbers, stated assumptions — a $90 loaded labor rate (derived above), 15% overhead, 20% target margin:
Panel upgrade, priced line by line
| Labor — 6 hrs at a loaded rate of $90/hr | $540 |
| Materials — panel, breakers, meter base, grounding | $780 |
| Permit & inspection fee | $185 |
| Overhead share — 15% of job cost | $226 |
| Total cost to the shop | $1,731 |
| Flat-rate price at a 20% margin ($1,731 ÷ 0.80) | $2,164 |
Quote the customer $2,164 before work starts. Notice where the money sits: the permit is a real line, not something absorbed "to be nice," and the price holds whether the job takes five hours or seven — which is exactly why the next example matters.
Worked example #2: an EV charger circuit
The job owners most often underprice, because the charger itself dominates the ticket and the circuit gets treated as an afterthought. Assume the charger is customer-supplied (or passed through at cost — either way, it isn't where your margin lives):
EV charger circuit (60-amp), priced line by line
| Labor — 2.5 hrs at a loaded rate of $90/hr | $225 |
| Materials — breaker, copper run, hardware | $385 |
| Permit & inspection fee | $95 |
| Overhead share — 15% of job cost | $106 |
| Total cost to the shop | $811 |
| Flat-rate price at a 20% margin ($811 ÷ 0.80) | $1,014 |
Now the gut-price version of the same job: "two and a half hours, call it $250, and we'll throw in the permit." That's $250 collected against $811 of cost — a $561 loss on a job the shop was happy to win, and the customer still thinks they paid for an expensive afternoon. The circuit was never cheap to deliver. It was only cheap to quote.
Pricing the diagnostic itself
One electrical-specific decision deserves its own paragraph: what to charge for finding the problem. Troubleshooting is skilled work with an open-ended clock — a dead circuit can be a tripped GFCI or a failed breaker or rodent damage in a wall — and it's the work shops most often give away. The shops that make money on service calls treat diagnosis as a priced line, not a courtesy: a diagnostic fee, stated at intake before the truck rolls, credited toward the repair when the customer approves it. The fee does three things at once. It pays for the finding-out. It filters for customers who value the answer. And it makes the repair quote calmer, because the customer has already said yes once. Put the diagnostic line first in your price book — in the template's example book it's the general line every trade shares — and never waive it silently. Waiving it "to be nice" trains customers that diagnosis is free and your time is the discount.
Emergency and after-hours calls
No-heat calls have a heating-season equivalent in electrical: no power to half the house, a burning smell from the panel, a dead well pump. After-hours work is where wage-based pricing fails hardest, because the true cost of a 9 p.m. callout — your evening, your rested-ness, tomorrow's first job — never appears in a journeyman rate. Price it as its own thing: an after-hours diagnostic line in the book, higher than the daytime one, stated on the phone before anyone rolls, with the repair itself still priced from the same book. Customers accept an after-hours fee they've heard before the truck moves; what they fight is a surprise on the invoice. Your written after-hours policy — fee, hours, what counts as an emergency — is a policy decision you make once, not a negotiation you have nightly.
Keep the book honest: review it twice a year
A price book is not a monument. Copper moves, breaker prices move, your burden changes when insurance renews, and your billable percentage changes when you add a truck. Twice a year — or whenever material prices jump — re-run the three numbers this guide started with: burdened wage, billable share, overhead percentage. Then spot-check five lines against your job-costing records: did the panel upgrades actually take six hours, or seven? Adjust the lines that reality disagrees with. A book that's reviewed on a schedule stays a pricing system; a book that isn't becomes last year's guess with better formatting.
Where electrical shops go wrong
- Free troubleshooting time. Forty minutes of diagnosis that ends in a quote the customer declines is a cost, not a courtesy. A diagnostic fee — stated at intake, credited toward the repair — is how shops stop donating it.
- Uncharged permit runs. The permit fee, the trip to the permit office or the time on the portal, the inspection wait — all real, all on the job. Price them in or list them as a line; don't absorb them silently.
- "While you're here" add-ons given away. The extra outlet, the wobbly ceiling fan, the dead doorbell — each is a price-book line with its own price. Small isn't free; small jobs carry the same drive time as big ones.
- Pricing off the wage, not the cost. $38/hour is what the electrician takes home. $90 is what the billable hour costs. Quoting from the first number is how busy shops go broke.
Your first 20 price-book lines
Don't build 200 lines. Build the twenty jobs you actually run, price each one with the method above, and let the book grow from real calls. For a service electrical shop, the first twenty usually look like this:
- Service diagnostic call
- 200-amp panel upgrade
- Breaker replacement
- EV charger circuit
- Ceiling fan install (existing box)
- Recessed lighting — set of four
- GFCI outlet replacement
- Whole-home surge protector
- Smoke / CO detector replacement (set)
- Hot tub circuit
- Dedicated appliance circuit
- Outdoor GFCI outlet
- Generator inlet with interlock
- Bath exhaust fan install
- Under-cabinet lighting
- Dimmer switch install
- 240V dryer / range outlet
- Attic fan install
- Landscape lighting run
- Doorbell / chime replacement
Twenty lines, priced from your costs, covers the large majority of a service electrician's week — and every quote after that is a lookup instead of an invention. The same method builds the book for the other trades: here's how it runs for HVAC jobs, and the thinking behind flat rate vs. time and materials if you're still deciding whether to switch at all.
Run your own numbers
The free FlatRateKit calculator does this exact math with your labor rate, overhead, and margin — including what a "small" discount really does to your profit.
Get the calculator, price book, and SOPs
The kit includes the full pricing calculator spreadsheet, the price-book template with electrical categories built in, the job-costing tracker, the SOP library, and the quote scripts that present the price without flinching.
Try the free calculator See the kit — $89